Leading 10 usual forklift crashes ， forklift procedure must focus on these matters ！.

Leading 10 usual forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Do not take too lightly the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the motorist's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the allowed size of the route and holds on the roadside shelf, which almost triggers an crash.
Case 4: Forklift is speeding up and rolls over throughout a turn.
Situation 5: The forklift driver did not see the pedestrian, and the pedestrian did not notice the forklift.
Situation 6: The forklift lifts the workers unlawfully, the forklift motorist does not put on the safety belt, the forklift lifter falls and the vehicle driver is squashed when the forklift surrender.
Situation 7: The forklift driver did not use a seat belt and dropped from the vehicle when it rolled over and was crushed.
Forklift operation need to take notice of these issues ：.

Start.
1. Before beginning, observe the environments, and after verifying that there are no challenges that impede the safety and security of driving, beep the horn initially and after that begin.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before starting.
3. When the forklift starts with a lots, the chauffeur needs to initially confirm that the lots is secure and reputable.
4. The beginning needs to be sluggish and consistent.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole ought to be slanted backward. .
2. Do not raise the fork too high when driving. When going into and leaving the job website or while driving, beware that there will certainly be no barriers overhead. When the tons is taking a trip, the fork needs to not be increased too expensive, which will influence the security of the forklift. .
3. After dumping, the fork needs to be lowered to the normal driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be released first. High-speed sharp turns are restricted. High-speed doglegs will cause the lorry to lose lateral security and topple. .
5. When the forklift is downhill, it is strictly forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with tons unless there are unique circumstances.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and need to keep a specific safety distance from the car in front. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry should be effectively slanted back. The load will not be increased except when piling or loading. .
8. The elevation of the load should not block the chauffeur's sight. In unique circumstances, when the item affects the forward vision, drive at a low rate when turning around.
9. It is forbidden to turn on the ramp, nor to drive throughout the ramp. .
10. The safe driving speed of the forklift in the factory area is 5 km/h, and it should drive safely at a low speed when going into the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is forbidden for personnel to stand on the fork to hold things and play a stabilizing role. .
12. If problems are discovered, they will certainly be fixed and reported in a prompt way, and they will never ever run with diseases or conceal them.

filling and dumping.
1. When fork-loading products, the range in between the two forks should be readjusted as needed to make the lots of both forks balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork pointer ought to not touch various other goods or objects. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide backwards. The pole can be slanted forward somewhat when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to participate in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or depress the parking brake button.
3. The engine is turned off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and air conditioning water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must also be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you come across somebody before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they come across huge or heavy items Stand-on Electric Pallet Stacker and go to the vehicle driver's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of Electric Forklift Truck for Warehouse the road, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844